[OpenIndiana-discuss] recognizing disks

[Mike La Spina]

Adam,

As I suspected it did not find a driver match. There is a Solaris driver
available from LSI for that card.
            
pci1000,9240 (driver not attached)

Try
http://www.lsi.com/channel/products/storagecomponents/Pages/MegaRAIDSAS9
240-8i.aspx
Or
http://www.byte.nl/blog/2011/01/04/how-to-install-opensolaris-openindian
a-on-an-m1015-lsi-9240-raid-controller/

Regards,
Mike
 


-----Original Message-----
From: Adam Gold [mailto:awg1 at gmx.com] 
Sent: Sunday, June 24, 2012 12:15 PM
To: Discussion list for OpenIndiana
Subject: Re: [OpenIndiana-discuss] recognizing disks

Mike,

Thanks a lot for the response.  The controller model is LSI 9240-8i.  I
ran the command and received the following output:

*************
 pci15d9,6 (driver not attached)
        pci8086,3408 (driver not attached)
        pci8086,340a (driver not attached)
        pci8086,340e (driver not attached)
            pci1000,9240 (driver not attached)
        pci8086,342d (driver not attached)
        pci8086,342e (driver not attached)
        pci8086,3422 (driver not attached)
        pci8086,3438 (driver not attached)
        pci15d9,6 (driver not attached)
        pci15d9,6 (driver not attached)
        pci15d9,6 (driver not attached)
        pci15d9,6 (driver not attached)
        pci15d9,6 (driver not attached)
        pci15d9,6 (driver not attached)
        pci15d9,6 (driver not attached)
        pci15d9,6 (driver not attached)
        pci15d9,6 (driver not attached)
                    input, instance #4 (driver not attached)
            motherboard (driver not attached)
            asy, instance #0 (driver not attached)
            asy, instance #1 (driver not attached)
            motherboard (driver not attached)
            ide (driver not attached)
        pci15d9,6 (driver not attached)
            ide (driver not attached)
    ioapics (driver not attached)
        ioapic, instance #0 (driver not attached)
    used-resources (driver not attached)
    agpgart, instance #0 (driver not attached)
*************

I'm guessing it's one of the pci drivers - any pointers (or questions I
can answer to help narrow it down).  Also, am I correct in saying the
loading of the Initiator/Target mode firmware image should be done in
the BIOS before the O/S has loaded?

Thanks for your help.

Regards,

Adam


On 24 Jun 2012, at 17:24, Mike La Spina wrote:

> Hi Adam,
> 
> Possibly the LSI controller was not matched to a driver. Check the 
> controller model and verify it is on the HCL.
> 
> Run: 
> 
> pfexec prtconf | grep driver
> 
> to observer any devices that are not bound to a driver.
> 
> 
> http://illumos.org/hcl/
> 
> Typically I have found that the some RAID mode firmware within LSI 
> cards and other vendors is not always compatible or matched to a
driver.
> For example I have an IBM (LSI 1068) branded adaptor. It works fine 
> when I load the Initiator/Target mode firmware image but not when it's

> running the RAID firmware image.
> 
> Regards,
> Mike
> 
> http://blog.laspina.ca/
> 
> 
> -----Original Message-----
> From: Adam Gold [mailto:awg1 at gmx.com]
> Sent: Sunday, June 24, 2012 9:28 AM
> To: openindiana-discuss at openindiana.org
> Subject: [OpenIndiana-discuss] recognizing disks
> 
> Hi there.  I'm a linux user and have recently decided to switch to 
> OpenIndiana using a x86_64 server.  Somewhat embarrassingly I'm seem 
> to be falling at one of the early hurdles.  My server has 1 SSD where 
> the O/S has been successfully installed and 4 X 3TB hard drives 
> managed by an LSI RAID controller.  I have configured the hard drives 
> as JBOD so I can use ZFS with all its capabilities.
> 
> Having booted up for the first time I ran 'format -e' but the 4 hard 
> drives were not detected.  Likewise when using 'cfgadm -alv' and 
> 'devfsadm' + 'format' there was no sign of any unconfigured drives.
> Just to be sure there wasn't any legacy data/meta-data I booted to a 
> rescue disk and erased the GPT labels at the beginning and end of the 
> 3TB disks using 'dd'.  Again no luck.
> 
> These drives have always showed up automatically under linux so I'm 
> wondering if I'm making some very obvious starting error with the new 
> O/S, perhaps to do with labelling (although now there really are no
> labels) or something.  I'm posting in the hope that this may be 
> quickly apparent to veteran users (and apologies for the relatively 
> trivial level of the inquiry).  Thanks in advance for any responses.
> _______________________________________________
> OpenIndiana-discuss mailing list
> OpenIndiana-discuss at openindiana.org
> http://openindiana.org/mailman/listinfo/openindiana-discuss
> 
> _______________________________________________
> OpenIndiana-discuss mailing list
> OpenIndiana-discuss at openindiana.org
> http://openindiana.org/mailman/listinfo/openindiana-discuss


_______________________________________________
OpenIndiana-discuss mailing list
OpenIndiana-discuss at openindiana.org
http://openindiana.org/mailman/listinfo/openindiana-discuss