[OpenIndiana-discuss] InfiniBand card not working

[Matt Breitbach]

The correct profile appears to be selected, and my configuration file is
below - I've also munged out the e1000g0 IP addresses, as those are public
facing IP addresses, and I'd rather not have them out there.

interface:e1000g1
type=uint64,1;class=uint64,1;parent=string,Automatic;enabled=boolean,true;ip
-version=uint64,4,6;ipv4-addrsrc=uint64,0;ipv6-addrsrc=uint64,0,1;
interface:e1000g0
type=uint64,1;class=uint64,1;parent=string,Automatic;enabled=boolean,true;ip
v4-default-route=string,X.X.X.X;ipv4-addr=string,X.X.X.X/24;ipv4-addrsrc=uin
t64,2;ipv6-addrsrc=uint64,0,1;ip-version=uint64,4,6;
interface:ibp1
type=uint64,1;class=uint64,1;parent=string,Automatic;enabled=boolean,true;ip
v4-default-route=string,10.0.1.254;ipv4-addr=string,10.0.1.79/24;ipv4-addrsr
c=uint64,2;ipv6-addrsrc=uint64,0,1;ip-version=uint64,4,6;
link:e1000g0
type=uint64,0;class=uint64,0;parent=string,Automatic;enabled=boolean,true;pr
iority-group=uint64,1;activation-mode=uint64,4;priority-mode=uint64,1;
link:e1000g1
type=uint64,0;class=uint64,0;parent=string,Automatic;enabled=boolean,true;ac
tivation-mode=uint64,4;priority-group=uint64,1;priority-mode=uint64,1;
link:ibp0
type=uint64,0;class=uint64,0;parent=string,Automatic;enabled=boolean,true;pr
iority-group=uint64,1;activation-mode=uint64,4;priority-mode=uint64,1;
link:ibp1
type=uint64,0;class=uint64,0;parent=string,Automatic;enabled=boolean,true;ac
tivation-mode=uint64,4;priority-group=uint64,1;priority-mode=uint64,1;
interface:ibp0
type=uint64,1;class=uint64,1;parent=string,Automatic;enabled=boolean,true;ip
v4-default-route=string,10.0.1.254;ipv4-addr=string,10.0.1.56/24;ipv4-addrsr
c=uint64,2;ip-version=uint64,4;

-----Original Message-----
From: Albert Lee [mailto:trisk at opensolaris.org] 
Sent: Sunday, October 17, 2010 9:15 PM
To: Discussion list for OpenIndiana
Subject: Re: [OpenIndiana-discuss] InfiniBand card not working>

"Waiting for address" shouldn't show up for a manual configuration,
make sure the correct profile is active by selecting "Network Profile"
from the "Show:" listbox. Selecting a profile and clicking "Edit" will
show the complete configuration for the profile, make sure it shows
the interface as "Address (v4) <address/prefix>, (v6) DHCP Assigned,
Autoconf" (or the reverse if you're using v6). The interface should
also be grouped under "Always enable these connections:".

If you've confirmed this, can you attach a copy of
/etc/nwam/ncp-User.conf (where "User" is the name of the active
profile in NWAM)?

-Albert

_______________________________________________
OpenIndiana-discuss mailing list
OpenIndiana-discuss at openindiana.org
http://openindiana.org/mailman/listinfo/openindiana-discuss